|
 |
 |
|
Flexible and Portable >> Flexible Cable
 |  Type W Magnet Crane
TYPE W MAGNET CRANE PORTABLE POWER CABLE - 600/2000 Volt,
EPDM Insulation, CPE Jacket, Stranded Copper Conductor, 90°C Dry, Wet
Type W Magnet Crane Portable Power Cable is recommended for installations where long flex life, greater flexibility and wearability are desired. The cable is designed for use on magnet cranes, mobile mining equipment, conveyors, drills and pumps, as portable power and temporary power supply where grounded circuits are not required. This cable may be used in wet or dry location at continuous conductor temperature of 90°C. This cable is constructed of ethylene propylene rubber (EPDM) insulation and heavy duty, extra hard usage thermoset chlorinated polyethylene (CPE) jacket.
Suitable for use in festoons, suspended loops and power tracks
May be installed in air, in ducts, immersed in water or directly buried in the earth
OSHA acceptable; MSHA listed
Excellent Flexibility
Passes MSHA flame test
Excellent resistance to oils, solvents, ozone, aging, and abrasion
Maximum continuous conductor temperature: 90°C DRY, 90°C WET
 
|  | | Application: Magnet cranes, mobile mining equipment, conveyors, drills and pumps | | Festoon Cable
FLAT FESTOONING CABLE - 600 Volt,
PVC Insulation, PVC Jacket, Stranded Copper Conductor, 105°C Dry, Wet
Festoon cable is flat cable designed for power and control applications of crane bridges and gantries, hoists, monorail systems, traveling electrified equipment and other mobile equipment utilizing a cantenary system for cable installation. In addition, festoon cable is suited to any variety of applications when engineering or design problem issues occur. The flat construction allows cables to be stacked for applications where space is at a premium. This cable is constructed of color-coded polyvinyl chloride (PVC) insulation and UV resistant polyvinyl chloride (PVC) jacket.
Flexible stranding
Sunlight/UV resistant insulation and jacket
Flame resistant, VW-1 rated
Small bending radius
Can be used indoors and outdoors
Oil and moisture resistant
Temperature Range: 105°C to -40°C
Maximum continuous conductor temperature: 105°C DRY, 105°C WET
|  | | Application: Cranes, hoists or any equipment which travels with lateral traversing motion | | Pendant and Reeling Cable
TYPE SOW PENDANT & REELING CABLE - 600 Volt,
EP Insulation, CPE Jacket, Stranded Copper Conductor, 90°C Dry, 60°C Wet
Pedant & Reeling Cable is a very flexible cable for use on cable tender systems, festooned cable applications, pendant cable drops, overhead bridge cranes, warehouse stacking cranes, motor- or spring-driven reels or any tough industrial application that requires both strength and flexibility. Designed and manufactured for use in continuous flexing applications where flame, abrasion, chemicals, moisture, impact, tearing, and temperature extremes are considerations.
For installation in cable trays, raceways supported by a messenger wire, open air and for direct burial applications
Flame, oil, solvent and sunlight resistant
Suitable for use in indoors and outdoors in severe flexing applications
High flexibility
Easy to solder and resists corrosion
MSHA approved
Maximum continuous conductor temperature: 90°C DRY, 60°C WET
|  | | Application: Cable tender systems, festooned cable applications, pendant cable drops, overhead bridge cranes, warehouse stacking cranes, motor- or spring-driven reels | | Bus Drop Cable
BUS DROP CABLE - 600 Volt,
PVC/Nylon Insulation, PVC Jacket, Stranded Copper Conductor, 75°C Dry, 75°C Wet
Bus Drop Cables are assembled round with three power conductors and three grounding conductors (one per interstice) with fillers as needed. Designed for indoor and outdoor use in wet or dry locations for the connection of portable or stationary equipment to facilitate their interchange. This allows for easy relocation of plant equipment. This cable is constructed with color-coded thermoplastic Insulation/Nylon insulation and a Sunlight resistant polyvinyl chloride (PVC) jacket.
Resistant to oils, lubricants, acids, alkalies, ozone, water and abrasion
Rated for use in wet or dry locations
Individual grounds per conductor
OSHA acceptable
Maximum continuous conductor temperature: 75°C DRY, 75°C WET
|  | | Application: Drop cables from overhead busways | | Type SDN
TYPE SDN FLEXIBLE CONTROL CABLE - 600 Volt,
Polymer/Nylon Insulation, Neoprene Jacket, Stranded Copper Conductor, 90°C Dry, 75°C Wet
Small Diameter Flexible Control Cable is multiconductor UL listed Type TC cable consisting of stranded, uncoated annealed copper, insulated with a flame retardant polymer and nylon jacket, cabled together with fillers, as required, mylar tape wrapped, and jacketed overall with a black low temperature, flame resistant, neoprene. Designed for control, power, lighting, telemetering, signal, relay traffic control, wherever flexible, small diameter cable is required such as cranes, hoists, and some robotics applications. The cable can be used indoors or outdoors; in pendant, reeling and other flexing applications down to -55°C. This cable is constructed with high dielectric flame retardant polymer with a clear polyamide (nylon) jacket extruded over primary insulation and a heavy duty, flame and oil resistant arctic grade neoprene (PVC) jacket.
For installation in trays, raceways, troughs, channels, ducts, conduit, and by direct burial
Recommended for wet or dry locations and outdoors in cable trays where a sunlight resistant rating is
required
Flame and oil resistant
Appropriate choice for tough flexing and reeling applications where mechanical ruggedness and small diameters are required
Temperature Range: 90°C to -55°C
Maximum continuous conductor temperature: 90°C DRY, 75°C WET
| 
 | | Application: Control, power, lighting, telemetering, signal, relay traffic control | | Type VFD
VARIBLE FREQUENCY DRIVE (VFD) POWER CABLE - 1000 Volt,
XLP Insulation, PVC Jacket, Stranded Copper Conductor, 90°C Dry, 90°C Wet
VFD cables are shielded, flexible motor supply cable for variable speed drives subject to non-linear power distortions. This cable is used to interconnect an AC variable frequency drive or control system, to an AC variable frequency motor. Variable Frequency AC motor drive output cables are subject to a harsh operating environment characterized by high voltage spikes, high noise levels and adverse environmental conditions. VFD cables were designed to overcome the shortcomings of unshielded tray cables, single conductor lead wire installed in conduit or continuously welded armored cable typically used in this application. This cable is constructed with crosslinked polyethylene (XLP) insulation and an UV and oil resistant polyvinyl chloride (PVC) jacket.
For installation in trays, raceways, troughs, channels, ducts, conduit, and by direct burial
Highly flexible tinned copper conductors with high strand counts
Easy to install and able to withstand tight minimum bending radii even during heavy vibration
Disperses voltage spikes, harmonics, and power distortions associated with variable frequency drives
Inner jacket is used to protect the insulation from the braid shield and to lower the capacitive interaction between the shield and power conductors
UV and oil resistant; Heat and moisture resistant
Maximum continuous conductor temperature: 90°C DRY, 90°C WET
| 
| | Application: AC variable frequency drive or control system, to an AC variable frequency motor | | Hook-Up Wire
Type MTW/AWM/TEW/TFFN HOOK-UP WIRE - 600V,
PVC Insulation, Single Conductor, 105°C Dry Location 60°C Wet Location
Type MTW/AWM/TEW/TFFN is primarily used as wiring in machine tools, appliances, and in various building applications as specified by the National Electrical Code. MTW/AWM/TEW/TFFN conductors are stranded, soft-annealed copper. The conductors are then insulated with a tough polyvinyl chloride (PVC), making the wire heat, moisture, and oil-resistant. The wire meets the requirements of the National Electrical Code and is listed by Underwriters Laboratories, Inc. and Canadian Standards Association.
Wire heat, moisture, and oil resistant insulation
Flexible stranding
MTW & AWM is flame retardant and meets the UL VW-1 flame test (TEW is FT1 rated)
Type MTW or AWM is UL Listed for machine tool wire and appliance wiring material
TEW is CSA rated for thermoplastic equipment wire
Nylon jacket on TFFN only
Maximum continuous conductor temperature: 105°C Dry, 60°C Wet
|  | | Application: Wiring in machine tools, appliances, and in various building applications; for use in transformers, ballasts, swichboard panels, controls, electronic circuits and motors | | Lamp Cord
TYPE SPT-1/SPT-2/SPT-3 LAMP CORD - 300 Volt,
PVC Insulation, Stranded Conductor, 105°C/60°C Dry
Lamp Cord is the parallel insulated type SPT which consists of two bare copper conductors laid flat with integral thermoplastic insulation and jacket. The cable is designed to be used where the nature of the service is not severe.
Bare stranded copper conductor
One conductor marked for polarity identification
Extra flexible stranded copper conductors
Parallel construction with mid web
Passes UL VW-1 & CSA FT1 vertical flame test
OSHA Acceptable
Maximum continuous conductor temperature:
SPT-1 105°C DRY
SPT-2 60°C and 105°C DRY
SPT-3 60°C DRY
|  | | Application: Household appliances, including lamps, clocks, fans, and radios | | Type HPN
TYPE HPN PARALLEL HEATER CORD - 300 Volt,
Neoprene Insulation, Stranded Conductor, 90°C Dry
Type HPN Cord is used with heating appliances such as toasters and flat irons. Type HPN is similar to type SPT with the exception that it's wall thickness is much greater and the insulation is specially compounded neoprene.
Extra flexible stranding and parallel construction makes cord easy to strip and connect
Green grounding conductor separates readily from circuit conductors for easy processability
Mechanically tough
Heat and oil resistant
Excellent resistance to acids, alkalies, sunlight and ozone
Maximum continuous conductor temperature: 90°C DRY
|  | | Application: Heating appliances, toasters, waffle irons, soldering irons, heat lamps, frying pans, coffee makers & similar devices | |
|
Specifications listed are from multiple manufacturers. The items above represent only a portion of the
products available. For specific manufacturer technical information or for an item not shown, please contact a Calvert Wire cabling specialist at 800-837-2668.
|
call today 800.837.2668 <> fax 216.433.7614 |
|
|
|
